EXPLORING BASIC PLUMBING WHEN YOU INSTALL A BATHTUB

Exploring Basic Plumbing When You Install a Bathtub

Exploring Basic Plumbing When You Install a Bathtub

Blog Article

Check Us Out

This article below pertaining to How to Install a Bathtub is incredibly stimulating. Don't bypass it.


How to Install a Bathtub Yourself
Setting up a tub isn't specifically rocket science, but it does call for solid plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult task. If the old tub is conveniently easily accessible, the job can move speedily; if you need to open up a wall surface to eliminate the old tub and also place the brand-new bath tub, the job is much harder. In either situation, the task is within a house handyman's skills, although you will certainly need an assistant to leave the old tub and set in the new one. Make certain you have qualified on your own for the job and fit trying it. Instead of working with a service provider to take control of a halfway-completed project, it is much better to think about utilizing one before you start. Opportunities are you might require a specialist plumber to make tube connections.
This short article will certainly assist you install a new bathtub in your bathroom if you have already purchased a new bathtub and also don't need to alter the arrangement of your previous water pipelines.
Your devices and also product checklist should make up the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you need to change old taps with brand-new ones as a part of your installation, then the first thing you should do is disconnect the water system. After doing so, turn on the taps to drain any type of water remaining in the system. The procedure of getting rid of the existing taps can be quite problematic as a result of the restricted access that is commonly the situation.
    Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have actually been removed, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from transforming throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any old securing substance.
    Before proceeding to fit the new faucets, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, after that you will need a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the existing supply pipes.
    If you need to fit a monobloc, after that you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next, place the tap in the placing opening in the bath/basin making certain that the washers remain in location in between the tap as well as the sink. Secure the tap in place with the maker offered backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical tap ports. The former kind must be connected to the tap finishes initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

    Installing the Tub


    Making use of the two wooden boards under its feet, position the bath tub in the called for placement. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four tiny points.
    The next objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub till the level reviews degree.
    To install taps, fit the bottom of the outermost versatile faucet connector to the ideal supply pipe by making a compression join; after that do the exact same for the various other faucet.
    Turn on the water as well as check all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the bath tub and also check the overflow outlet as well as the typical outlet for leakages.
    Lastly, take care of the bath paneling as defined in the maker's user's manual. Tiling and sealing around the bath tub ought to wait until the bathtub has actually been used at least when as this will certainly settle it into its final setting.

    Getting ready for the Setup


    First of all, the sustaining frame provided with the bath ought to be fitted (if needed) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to avoid strain on the bath tub.
    Fit the adaptable faucet connectors to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use all of the provided washers.
    Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its last position.

    Tiling Around the Bathtub


    In the area where the bath meets the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, creating the water to pass through the wall surface between the bathroom and also the tiling, leading to difficulties with moisture and also possible leakages to the ceiling listed below.
    You can select from a range of coloured sealers to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and can sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to enable the motion experienced when the tub is in usage. The sealant can fracture relatively early if you do not take into account this activity before sealing.
    Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally easily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    We were shown that editorial on Installing A Bathtub through an acquaintance on another blog. Sharing is nice. Helping people is fun. We value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


    Top service, dial!

    Report this page